TB6600 Stepper Motor Driver

 1,200

TB6600 Arduino Stepper Motor Driver is an easy-to-use professional stepper motor driver, which
could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers
that can output a 5V digital pulse signal. TB6600 Arduino stepper motor driver has a wide range of
power input, 9~42VDC power supply. And it is able to output 4A peak current, which is enough for
most of stepper motors.
The stepper driver supports speed and direction control. You can set its micro-step and output
current with a 6 DIP switch. There are 7 kinds of micro-steps (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 kinds of
current control (0.5A, 1A, 1.5A, 2A, 2.5A, 2.8A, 3.0A, 3.5A) in all. And all signal terminals adopt high-speed optocoupler isolation, enhancing their anti-high-frequency interference ability.
As a professional device, it is able to drive 57, 42-type two-phase, four-phase, hybrid stepper motor.

Out of stock

Description

TB6600 Arduino Stepper Motor Driver is an easy-to-use professional stepper motor driver, which
could control a two-phase stepping motor. It is compatible with Arduino and other microcontrollers
that can output a 5V digital pulse signal. TB6600 Arduino stepper motor driver has a wide range of
power input, 9~42VDC power supply. And it is able to output 4A peak current, which is enough for
most of stepper motors.
The stepper driver supports speed and direction control. You can set its micro-step and output
current with a 6 DIP switch. There are 7 kinds of micro-steps (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 kinds of
current control (0.5A, 1A, 1.5A, 2A, 2.5A, 2.8A, 3.0A, 3.5A) in all. And all signal terminals adopt high-speed optocoupler isolation, enhancing their anti-high-frequency interference ability.
As a professional device, it is able to drive 57, 42-type two-phase, four-phase, hybrid stepper motor.

Features:

  • 9V-42V DC power supply.
  • Output current: 0.5A-4.0A.
  • Drive mode: Dual constant current PWM drive output.
  • Strong anti-interference ability.
  • Low vibration, low noise.
  • Insulation resistance: >500MΩ at normal temperature and pressure.
  • Insulation strength: 500V/min at normal temperature and pressure.
  • With overheating, overcurrent, under-voltage lockout, input voltage anti-reverse protection, and
    other functions.
  • Can drive 4-wire, 6-wire, 8-wire stepper motors.

 

Environmental Requirments:
Cooling method: natural cooling or forced air cooling.
Storage temperature: -20°C-65° C.
Ambient humidity: <80% RH, no condensation, no frost.
Vibration: maximum not exceeding 5.7m/S2.
Use occasions: Avoid dust, oil, and corrosive gases, and prohibit flammable gases and conductive
dust.

Wiring Requirments:
The pulse and direction signal lines and the motor and power lines are not allowed to be side by
side, preferably separated by at least 10 cm.
If one power supply is used for multiple drives, parallel connections should be made at the power
supply. It is not allowed to go to one another and then to another chain connection.
Do not plug or unplug the drive power terminal when the power is on. When the powered motor
stops, there is still a large current flowing through the coil. Pulling the power terminal will burn the
driver.
It is strictly forbidden to access terminal after wire head plus tin, otherwise, the terminal may be
overheated and damaged due to the contact resistance becomes larger.
The wiring heads should not be exposed outside the terminals to prevent accidental short circuits
and damage the drive.

Package Contains:

1 x TB6600 Driver

Additional information

Weight 300 g

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.